Hi
I have a strange problem. On initial start up, the IAC valve does not close at the 160 deg water temp. Upon re start, it will idle down. Seems strange. Has any one seen this problem?
Scott Bruce 69 Turbo Lotus Europa
Iac MSII 3.0 board
Forum rules
Read the manual to see if your question is answered there before posting. If you have questions about MS1/Extra or MS2/Extra or other non-B&G code configuration or tuning, please post them at http://www.msextra.com The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. If you have questions about MS1/Extra or MS2/Extra or other non-B&G code configuration or tuning, please post them at http://www.msextra.com The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
Scott Bruce
- MegaSquirt Newbie
- Posts: 17
- Joined: Tue May 02, 2006 8:13 pm
- Location: Massachusetts
-
Bernard Fife
- Super Squirter
- Posts: 1009
- Joined: Mon Feb 16, 2004 3:15 pm
Scott,
See this: http://www.msefi.com/viewtopic.php?t=17742
The bottom line is that some people are still experiencing this, even after jumpering resistors and implementing other tips from that thread, but it's not clear why.
Lance.
See this: http://www.msefi.com/viewtopic.php?t=17742
The bottom line is that some people are still experiencing this, even after jumpering resistors and implementing other tips from that thread, but it's not clear why.
Lance.
-
BottleFed70
- Helpful Squirter
- Posts: 91
- Joined: Fri Jun 24, 2005 2:22 pm
-
ronsonol
- MegaSquirt Newbie
- Posts: 32
- Joined: Thu Sep 23, 2004 7:48 pm
- Location: Kingston, ON, Canada
Yes, I see the same thing from time to time. And its very inconsistent, so its hard to troubleshoot.
I'll start the car and the idle will stay high, and the iac won't begin to close at all. Turn off, and immediately re-start, will fix the problem. Still following threads for that perfect solution.
I'll start the car and the idle will stay high, and the iac won't begin to close at all. Turn off, and immediately re-start, will fix the problem. Still following threads for that perfect solution.
1983 Jaguar XJS, 355 SBC TPI powered by MSII/V3 running code 2.684/MT 2.25, LC-1 wbO2, 7-pin HEI ignition
1986 Jaguar XJ12, V12, future project?
1986 Jaguar XJ12, V12, future project?
-
Scott Bruce
- MegaSquirt Newbie
- Posts: 17
- Joined: Tue May 02, 2006 8:13 pm
- Location: Massachusetts
IAC
I'm not sure of the firmware. My brother installed it. It was installed about 2 months ago and i believe it was the latest at that time.
Scott
Scott
-
BottleFed70
- Helpful Squirter
- Posts: 91
- Joined: Fri Jun 24, 2005 2:22 pm
Re: IAC
That's most likely the problem then. There was a bug in the firmware that was just fixed a month or so ago that caused the exact symptoms you are talking of. You need to upgrade the firmware to version 2.36Scott Bruce wrote:I'm not sure of the firmware. My brother installed it. It was installed about 2 months ago and i believe it was the latest at that time.
Scott
1970 Ford Mustang
MSII, v3.0 PCB, v2.36 firmware, Megatune 2.25
MSII, v3.0 PCB, v2.36 firmware, Megatune 2.25