Page 1 of 1
Another autotune question
Posted: Wed Aug 30, 2006 1:09 pm
by Avinitlarge
Code: Select all
[AutoTune]
#if MS_I
table = veTableMap ; Should be the map3d_id of a TableEditor entry.
allowAutoTune = on ; Displays the check box on the specified tuning dialog.
corrector = egoCorrection ; Variable used for correction algorithm.
; Tuning block parameters
; Global limits on tuning, outside the box and nothing happens.
xLimits = 1500, 4000 ; RPM
yLimits = 60, 90 ; MAP
zLimits = 10, 200 ; VE
; Vertex tolerance parameters
; How close you must be to a vertex before tuning takes place.
xRadius = 200 ; RPM
yRadius = 7 ; MAP
; Controller parameters
initialStartupInterval = 1.0 ; Seconds before first adjustment
updateInterval = 1.0 ; Seconds between each consecutive adjustment.
proportionalGain = 0.5 ; Proportion of (100-corrector) to use for adjustment.
lumpiness = 5 ; Maximum percent adjustment above or below neighboring VE points.
What would I change the setting to for use with a boosted engine and how could I use autotune upto 7000 rpm??
Posted: Wed Aug 30, 2006 1:29 pm
by Bernard Fife
Avinitlarge,
You edit the xLimits (to something like 1500, 7000) and yLimits (to something like 60, 200). There's more here:
http://www.megamanual.com/megatune.htm#autotune
However, you should be sure to understand what this is doing, as well as the risks of doing this.
Lance.
Posted: Wed Aug 30, 2006 3:05 pm
by Avinitlarge
I think that is pretty easy to understand apart from 1 tiny part In order to use auto-tune for WOT tuning, you must be running a wide band lambda system (sensor and controller), with an appropriate EGO correction algorithm that allows you to set specific AFR targets (i.e., MSnS-Extra or MS-II). If one of these requirements is missing, then you must rely on seat-of-the-pants and experience.
.
What is this ??
with an appropriate EGO correction algorithm that allows you to set specific AFR targets
Would this be it??
Under "Exhaust Gas Settings"
EGO Sensor Type : Wideband
EGO Switch Point : 2.352
Ignition Events pe Step : 4
Controller Step Size : 5
Controller Authority :75
Active Above Coolant Temp : 71*C
Active Above RPM : 1300
Under "Lambda AFR Setting"
Change EGO Limit above (kpa) : 255
Change EGO Limit (+-) : 5
For VE Table 1 : ON
For VE Table 2 : Off*^(DT)
Control Algorithm for AFR tables : Speed Density
Use Target Tables : Always
Posted: Fri Sep 01, 2006 9:36 am
by Avinitlarge
I know there is a post about this somewhere but I cant find that either, What are the Minimum Requirements for autoTune?
I have a PIII 500/700MHZ with 512Mb of ram, Will this do??
Another autotune question
Posted: Fri Sep 01, 2006 10:50 am
by sparkandfuel.com
You're in man! welcome to the club
Minimum requirements are pentium class, windows 95 and higher. I think the slowest I've heared of with autotune is 266MHz 32MB ram running win95, worked fine. lowest powered lappy running Megatune I've hered of is 66MHz, 16MB ram.
-gary-
www.SparkandFuel.com
Posted by email.
Posted: Sun Sep 03, 2006 2:25 am
by boost junkie
I use a P1 150mhz with 32mb running win98. Works fine.